This page uses content from Wikipedia and is licensed under CC BY-SA.
Young's modulus | |
---|---|
A given uniaxial stress, whether tensile (extension) or compressive (compression) creates more deformation in a material with low stiffness (red) than with a high stiffness (blue). Young's modulus is a measure of stiffness. | |
Common symbols | E, Y |
SI unit | pascal |
In SI base units | Pa = kg m^{−1} s^{−2} |
Derivations from other quantities | |
Dimension | M L^{−1} T^{−2} |
Young's modulus or Young modulus is a mechanical property that measures the stiffness of a solid material. It defines the relationship between stress (force per unit area) and strain (proportional deformation) in a material in the linear elasticity regime of a uniaxial deformation.
Young's modulus is named after the 19th-century British scientist Thomas Young. However, the concept was developed in 1727 by Leonhard Euler, and the first experiments that used the concept of Young's modulus in its current form were performed by the Italian scientist Giordano Riccati in 1782, pre-dating Young's work by 25 years.^{[1]} The term modulus is the diminutive of the Latin term modus which means measure.
A solid material will undergo elastic deformation when a small load is applied to it in compression or extension. Elastic deformation is reversible (the material returns to its original shape after the load is removed).
At near-zero stress and strain, the stress–strain curve is linear, and the relationship between stress and strain is described by Hooke's law that states stress is proportional to strain. The coefficient of proportionality is Young's modulus. The higher the modulus, the more stress is needed to create the same amount of strain; an idealized rigid body would have an infinite Young's modulus.
Not many materials are linear and elastic beyond a small amount of deformation.^{[citation needed]}
, where^{[2]}
In practice, Young's moduli are given in megapascals (MPa or N/mm^{2}) or gigapascals (GPa or kN/mm^{2}).
Material stiffness should not be confused with these properties:
Young's modulus enables the calculation of the change in the dimension of a bar made of an isotropic elastic material under tensile or compressive loads. For instance, it predicts how much a material sample extends under tension or shortens under compression. The Young's modulus directly applies to cases of uniaxial stress, that is tensile or compressive stress in one direction and no stress in the other directions. Young's modulus is also used in order to predict the deflection that will occur in a statically determinate beam when a load is applied at a point in between the beam's supports. Other elastic calculations usually require the use of one additional elastic property, such as the shear modulus, bulk modulus or Poisson's ratio. Any two of these parameters are sufficient to fully describe elasticity in an isotropic material.
Young's modulus represents the factor of proportionality in Hooke's law, which relates the stress and the strain. However, Hooke's law is only valid under the assumption of an elastic and linear response. Any real material will eventually fail and break when stretched over a very large distance or with a very large force; however all solid materials exhibit nearly Hookean behavior for small enough strains or stresses. If the range over which Hooke's law is valid is large enough compared to the typical stress that one expects to apply to the material, the material is said to be linear. Otherwise (if the typical stress one would apply is outside the linear range) the material is said to be non-linear.
Steel, carbon fiber and glass among others are usually considered linear materials, while other materials such as rubber and soils are non-linear. However, this is not an absolute classification: if very small stresses or strains are applied to a non-linear material, the response will be linear, but if very high stress or strain is applied to a linear material, the linear theory will not be enough. For example, as the linear theory implies reversibility, it would be absurd to use the linear theory to describe the failure of a steel bridge under a high load; although steel is a linear material for most applications, it is not in such a case of catastrophic failure.
In solid mechanics, the slope of the stress–strain curve at any point is called the tangent modulus. It can be experimentally determined from the slope of a stress–strain curve created during tensile tests conducted on a sample of the material.
Young's modulus is not always the same in all orientations of a material. Most metals and ceramics, along with many other materials, are isotropic, and their mechanical properties are the same in all orientations. However, metals and ceramics can be treated with certain impurities, and metals can be mechanically worked to make their grain structures directional. These materials then become anisotropic, and Young's modulus will change depending on the direction of the force vector. Anisotropy can be seen in many composites as well. For example, carbon fiber has a much higher Young's modulus (is much stiffer) when force is loaded parallel to the fibers (along the grain). Other such materials include wood and reinforced concrete. Engineers can use this directional phenomenon to their advantage in creating structures.
Young's modulus E, can be calculated by dividing the tensile stress, , by the engineering extensional strain, , in the elastic (initial, linear) portion of the physical stress–strain curve:
where
The Young's modulus of a material can be used to calculate the force it exerts under specific strain.
where F is the force exerted by the material when contracted or stretched by .
Hooke's law for a stretched wire can be derived from this formula:
where it comes in saturation
But note that the elasticity of coiled springs comes from shear modulus, not Young's modulus.
The elastic potential energy stored in a linear elastic material is given by the integral of the Hooke's law:
now by expliciting the intensive variables:
This means that the elastic potential energy density (i.e., per unit volume) is given by:
or, in simple notation, for a linear elastic material: , since the strain is defined .
In a nonlinear elastic material the Young's modulus is a function of the strain, so the second equivalence no longer holds and the elastic energy is not a quadratic function of the strain:
For homogeneous isotropic materials simple relations exist between elastic constants (Young's modulus E, shear modulus G, bulk modulus K, and Poisson's ratio ν) that allow calculating them all as long as two are known:
Young's modulus can vary somewhat due to differences in sample composition and test method. The rate of deformation has the greatest impact on the data collected, especially in polymers. The values here are approximate and only meant for relative comparison.
Material | GPa | Mpsi |
---|---|---|
Rubber (small strain) | 0.01–0.1^{[3]} | 1.45–×10^{−3} 14.5 |
Low-density polyethylene^{[4]} | 0.11–0.86 | 1.6–×10^{−2} 6.5 |
Diatom frustules (largely silicic acid)^{[5]} | 0.35–2.77 | 0.05–0.4 |
PTFE (Teflon) | 0.5^{[3]} | 0.075 |
HDPE | 0.8 | 0.116 |
Bacteriophage capsids^{[6]} | 1–3 | 0.15–0.435 |
Polypropylene | 1.5–2^{[3]} | 0.22–0.29 |
Polycarbonate | 2–2.4 | 0.29-0.36 |
Polyethylene terephthalate (PET) | 2–2.7^{[3]} | 0.29–0.39 |
Nylon | 2–4 | 0.29–0.58 |
Polystyrene, solid | 3–3.5^{[3]} | 0.44–0.51 |
Polystyrene, foam^{[7]} | 0.0025–0.007 | 0.00036–0.00102 |
Medium-density fiberboard (MDF)^{[8]} | 4 | 0.58 |
Wood (along grain) | 11^{[3]} | 1.60 |
Human Cortical Bone^{[9]} | 14 | 2.03 |
Glass-reinforced polyester matrix^{[10]} | 17.2 | 2.49 |
Aromatic peptide nanotubes^{[11]}^{[12]} | 19–27 | 2.76–3.92 |
High-strength concrete | 30^{[3]} | 4.35 |
Amino-acid molecular crystals^{[13]} | 21–44 | 3.04–6.38 |
Carbon fiber reinforced plastic (50/50 fibre/matrix, biaxial fabric) | 30–50^{[14]} | 4.35–7.25 |
Hemp fiber^{[15]} | 35 | 5.08 |
Magnesium metal (Mg) | 45^{[3]} | 6.53 |
Glass (see chart)^{[specify]} | 50–90^{[3]} | 7.25–13.1 |
Flax fiber^{[16]} | 58 | 8.41 |
Aluminum | 69^{[3]} | 10 |
Mother-of-pearl (nacre, largely calcium carbonate)^{[17]} | 70 | 10.2 |
Aramid^{[18]} | 70.5–112.4 | 10.2–16.3 |
Tooth enamel (largely calcium phosphate)^{[19]} | 83 | 12 |
Stinging nettle fiber^{[20]} | 87 | 12.6 |
Bronze | 96–120^{[3]} | 13.9–17.4 |
Brass | 100–125^{[3]} | 14.5–18.1 |
Titanium (Ti) | 110.3 | 16^{[3]} |
Titanium alloys | 105–120^{[3]} | 15–17.5 |
Copper (Cu) | 117 | 17 |
Carbon fiber reinforced plastic (70/30 fibre/matrix, unidirectional, along fibre)^{[21]} | 181 | 26.3 |
Silicon Single crystal, different directions^{[22]}^{[23]} | 130–185 | 18.9–26.8 |
Wrought iron | 190–210^{[3]} | 27.6–30.5 |
Steel (ASTM-A36) | 200^{[3]} | 29 |
polycrystalline Yttrium iron garnet (YIG)^{[24]} | 193 | 28 |
single-crystal Yttrium iron garnet (YIG)^{[25]} | 200 | 29 |
Cobalt-chrome (CoCr)^{[26]} | 220–258 | 29 |
Aromatic peptide nanospheres^{[27]} | 230–275 | 33.4–40 |
Beryllium (Be)^{[28]} | 287 | 41.6 |
Molybdenum (Mo) | 329–330^{[3]}^{[29]}^{[30]} | 47.7–47.9 |
Tungsten (W) | 400–410^{[3]} | 58–59 |
Silicon carbide (SiC) | 450^{[3]} | 65 |
Tungsten carbide (WC) | 450–650^{[3]} | 65–94 |
Osmium (Os) | 525–562^{[31]} | 76.1–81.5 |
Single-walled carbon nanotube | 1,000+^{[32]}^{[33]} | 150+ |
Graphene (C) | 1050^{[34]} | 152 |
Diamond (C) | 1050–1210^{[35]} | 152–175 |
Carbyne (C)^{[36]} | 32100^{[37]} | 4,660 |
Conversion formulae | |||||||
---|---|---|---|---|---|---|---|
Homogeneous isotropic linear elastic materials have their elastic properties uniquely determined by any two moduli among these; thus, given any two, any other of the elastic moduli can be calculated according to these formulas. | |||||||
Notes | |||||||
There are two valid solutions. | |||||||
Cannot be used when | |||||||