This page uses content from Wikipedia and is licensed under CC BY-SA.
Weighted arithmetic mean
"Weighted average" redirects here. It is not to be confused with Weighted median.
The weighted arithmetic mean is similar to an ordinary arithmetic mean (the most common type of average), except that instead of each of the data points contributing equally to the final average, some data points contribute more than others. The notion of weighted mean plays a role in descriptive statistics and also occurs in a more general form in several other areas of mathematics.
If all the weights are equal, then the weighted mean is the same as the arithmetic mean. While weighted means generally behave in a similar fashion to arithmetic means, they do have a few counterintuitive properties, as captured for instance in Simpson's paradox.
The straight average for the morning class is 80 and the straight average of the afternoon class is 90. The straight average of 80 and 90 is 85, the mean of the two class means. However, this does not account for the difference in number of students in each class (20 versus 30); hence the value of 85 does not reflect the average student grade (independent of class). The average student grade can be obtained by averaging all the grades, without regard to classes (add all the grades up and divide by the total number of students):
Or, this can be accomplished by weighting the class means by the number of students in each class (using a weighted mean of the class means):
Thus, the weighted mean makes it possible to find the average student grade in the case where only the class means and the number of students in each class are available.
Convex combination example
Since only the relative weights are relevant, any weighted mean can be expressed using coefficients that sum to one. Such a linear combination is called a convex combination.
Using the previous example, we would get the following weights:
(where x represents a set of mean values)
with non-negative weights
Therefore, data elements with a high weight contribute more to the weighted mean than do elements with a low weight. The weights cannot be negative. Some may be zero, but not all of them (since division by zero is not allowed).
The formulas are simplified when the weights are normalized such that they sum up to , i.e.:
For such normalized weights the weighted mean is then:
Note that one can always normalize the weights by making the following transformation on the original weights:
Using the normalized weight yields the same results as when using the original weights:
The ordinary mean is a special case of the weighted mean where all data have equal weights, .
The weighted sample mean, , is itself a random variable. Its expected value and standard deviation are related to the expected values and standard deviations of the observations, as follows. For simplicity, we assume normalized weights (weights summing to one).
If the observations have expected values
then the weighted sample mean has expectation
In particular, if the means are equal, , then the expectation of the weighted sample mean will be that value,
For uncorrelated observations with variances , the variance of the weighted sample mean is
whose square root can be called the standard error of the weighted mean (general case).
Consequently, if all the observations have equal variance, , the weighted sample mean will have variance
where . The variance attains its maximum value, , when all weights except one are zero. Its minimum value is found when all weights are equal (i.e., unweighted mean), in which case we have , i.e., it degenerates into the standard error of the mean, squared.
Note that because one can always transform non-normalized weights to normalized weights all formula in this section can be adapted to non-normalized weights by replacing all .
For the weighted mean of a list of data for which each element potentially comes from a different probability distribution with known variance, one possible choice for the weights is given by the reciprocal of variance:
The weighted mean in this case is:
and the standard error of the weighted mean (with variance weights) is:
Note this reduces to when all .
It is a special case of the general formula in previous section,
Weighted means are typically used to find the weighted mean of historical data, rather than theoretically generated data. In this case, there will be some error in the variance of each data point. Typically experimental errors may be underestimated due to the experimenter not taking into account all sources of error in calculating the variance of each data point. In this event, the variance in the weighted mean must be corrected to account for the fact that is too large. The correction that must be made is
Typically when a mean is calculated it is important to know the variance and standard deviation about that mean. When a weighted mean is used, the variance of the weighted sample is different from the variance of the unweighted sample.
The biased weighted sample variance is defined similarly to the normal biased sample variance :
where , which is 1 for normalized weights. If the weights are frequency weights (and thus are random variables), it can be shown that is the maximum likelihood estimator of for iid Gaussian observations.
For small samples, it is customary to use an unbiased estimator for the population variance. In normal unweighted samples, the N in the denominator (corresponding to the sample size) is changed to N − 1 (see Bessel's correction). In the weighted setting, there are actually two different unbiased estimators, one for the case of frequency weights and another for the case of reliability weights.
If the weights are frequency weights, then the unbiased estimator is:
This effectively applies Bessel's correction for frequency weights.
For example, if values are drawn from the same distribution, then we can treat this set as an unweighted sample, or we can treat it as the weighted sample with corresponding weights , and we get the same result either way.
If the frequency weights are normalized to 1, then the correct expression after Bessel's correction becomes
where the total number of samples is (not ). In any case, the information on total number of samples is necessary in order to obtain an unbiased correction, even if has a different meaning other than frequency weight.
If the weights are instead non-random (reliability weights), we can determine a correction factor to yield an unbiased estimator. Assuming each random variable is sampled from the same distribution with mean and actual variance , taking expectations we have,
where . Therefore, the bias in our estimator is , analogous to the bias in the unweighted estimator. This means that to unbias our estimator we need to pre-divide by , ensuring that the expected value of the estimated variance equals the actual variance of the sampling distribution.
The final unbiased estimate of sample variance is:
and the unbiased weighted estimate of the covariance matrix is:
The reasoning here is the same as in the previous section.
Since we are assuming the weights are normalized, then and this reduces to:
If all weights are the same, i.e. , then the weighted mean and covariance reduce to the unweighted sample mean and covariance above.
The above generalizes easily to the case of taking the mean of vector-valued estimates. For example, estimates of position on a plane may have less certainty in one direction than another. As in the scalar case, the weighted mean of multiple estimates can provide a maximum likelihood estimate. We simply replace the variance by the covariance matrix and the arithmetic inverse by the matrix inverse (both denoted in the same way, via superscripts); the weight matrix then reads:
Consider the time series of an independent variable and a dependent variable , with observations sampled at discrete times . In many common situations, the value of at time depends not only on but also on its past values. Commonly, the strength of this dependence decreases as the separation of observations in time increases. To model this situation, one may replace the independent variable by its sliding mean for a window size .
In the scenario described in the previous section, most frequently the decrease in interaction strength obeys a negative exponential law. If the observations are sampled at equidistant times, then exponential decrease is equivalent to decrease by a constant fraction at each time step. Setting we can define normalized weights by
where is the sum of the unnormalized weights. In this case is simply
approaching for large values of .
The damping constant must correspond to the actual decrease of interaction strength. If this cannot be determined from theoretical considerations, then the following properties of exponentially decreasing weights are useful in making a suitable choice: at step , the weight approximately equals , the tail area the value , the head area . The tail area at step is . Where primarily the closest observations matter and the effect of the remaining observations can be ignored safely, then choose such that the tail area is sufficiently small.
Weighted averages of functions
The concept of weighted average can be extended to functions. Weighted averages of functions play an important role in the systems of weighted differential and integral calculus.