This page uses content from Wikipedia and is licensed under CC BY-SA.
ISO/IEC 7816 is an international standard related to electronic identification cards with contacts, especially smart cards, managed jointly by the International Organization for Standardization (ISO) and the International Electrotechnical Commission (IEC).
It is edited by the Joint technical committee (JTC) 1 / Sub-Committee (SC) 17, Cards and personal identification.
The following describes the different parts of this standard.
Created in 1987, updated in 1998, amended in 2003, updated in 2011.
This part describes the physical characteristics of the card, primarily by reference to ISO/IEC 7810 Identification cards — Physical characteristics, but also with other characteristics such as mechanical strength.
Created in 1988, updated in 1999, amended in 2004, updated in 2007.
Created in 1989, amended in 1992 (addition of the T=1 protocol), amended in 1994 (revision of Protocol Type Selection), updated in 1997 (including addition of 3 Volt operation), amended in 2002 (including addition of 1.8 Volt operation), last updated in 2006 (including removal of Vpp).
According to its abstract, it specifies:
It does not cover the internal implementation within the card or the outside world.
Created in 1995, updated in 2004.
According to its abstract, ISO/IEC 7816-5 defines how to use an application identifier to ascertain the presence of and/or perform the retrieval of an application in a card.
ISO/IEC 7816-5:2004 shows how to grant the uniqueness of application identifiers through the international registration of a part of this identifier, and defines
Created in 1996, updated in 2004, amended in 2006, updated in 2016.
According to its abstract, it specifies the Data Elements (DEs) used for interindustry interchange based on integrated circuit cards (ICCs) both with contacts and without contacts. It gives the identifier, name, description, format, coding and layout of each DE and defines the means of retrieval of DEs from the card.
Created in 1999.
Created in 1995, updated in 2004, updated in 2016.
According to its abstract, it specifies interindustry commands for integrated circuit cards (either with contacts or without contacts) that may be used for cryptographic operations. These commands are complementary to and based on the commands listed in ISO/IEC 7816-4.
Annexes are provided that give examples of operations related to digital signatures, certificates and the import and export of asymmetric keys.
The choice and conditions of use of cryptographic mechanisms may affect card exportability. The evaluation of the suitability of algorithms and protocols is outside the scope of ISO/IEC 7816-8.
Created in 1995, updated in 2004, updated in 2017.
According to its abstract, it specifies interindustry commands for integrated circuit cards (both with contacts and without contacts) for card and file management, e.g. file creation and deletion. These commands cover the entire life cycle of the card and therefore some commands may be used before the card has been issued to the cardholder or after the card has expired.
An annex is provided that shows how to control the loading of data (secure download) into the card, by means of verifying the access rights of the loading entity and protection of the transmitted data with secure messaging. The loaded data may contain, for example, code, keys and applets.
Created in 1999.
This part specifies the power, signal structures, and the structure for the answer to reset between an integrated circuit card(s) with synchronous transmission and an interface device such as a terminal.
Created in 2004, updated in 2017.
This part of ISO/IEC 7816 specifies security-related interindustry commands to be used for personal verification through biometric methods in integrated circuit cards. It also defines the data structure and data access methods for use of the card as a carrier of the biometric reference and/or as the device to perform the verification of the cardholder’s biometric probe (on-card biometric comparison). Identification of persons using biometric methods is outside the scope of this standard.
Created in 2005.
According to its abstract, it specifies the operating conditions of an integrated circuit card that provides a USB interface. An integrated circuit card with a USB interface is named USB-ICC.
ISO/IEC 7816-12:2005 specifies:
ISO/IEC 7816-12:2005 provides two protocols for control transfers. This is to support the protocol T=0 (version A) or to use the transfer on APDU level (version B). ISO/IEC 7816-12:2005 provides the state diagrams for the USB-ICC for each of the transfers (bulk transfers, control transfers version A and version B). Examples of possible sequences which the USB-ICC must be able to handle are given in an informative annex.
The USB CCID device class defines a standard for communicating with ISO/IEC 7816 smart cards over USB.
This part specifies commands for application management in a multi-application environment.
Created in 2004, amended in 2004, 2007, 2008, updated in 2016.
According to its abstract, it specifies a card application. This application contains information on cryptographic functionality. Further, ISO/IEC 7816-15:2016 defines a common syntax (in ASN.1) and format for the cryptographic information and mechanisms to share this information whenever appropriate.
ISO/IEC 7816-15:2016 supports the following capabilities: