A hydrofoil is a lifting surface, or foil, that operates in water. They are similar in appearance and purpose to aerofoils used by aeroplanes. Boats that use hydrofoil technology are also simply termed hydrofoils. As a hydrofoil craft gains speed, the hydrofoils lift the boat's hull out of the water, decreasing drag and allowing greater speeds.
The hydrofoil usually consists of a wing like structure mounted on struts below the hull, or across the keels of a catamaran in a variety of boats (see illustration). As a hydrofoil-equipped watercraft increases in speed, the hydrofoil elements below the hull(s) develop enough lift to raise the hull out of the water, which greatly reduces hull drag. This provides a corresponding increase in speed and fuel efficiency.
Wider adoption of hydrofoils is prevented by the increased complexity of building and maintaining them. Hydrofoils are generally prohibitively more expensive than conventional watercraft above the certain displacement, so most hydrofoil craft are relatively small, and are mainly used as high-speed passenger ferries, where the relatively high passenger fees can offset the high cost of the craft itself. However, the design is simple enough that there are many human-powered hydrofoil designs. Amateur experimentation and development of the concept is popular.
Since air and water are governed by similar fluid equations—albeit with different levels of viscosity, density, and compressibility—the hydrofoil and airfoil (both types of foil) create lift in identical ways. The foil shape moves smoothly through the water, deflecting the flow downward, which, following the Euler equations, exerts an upward force on the foil. This turning of the water creates higher pressure on the bottom of the foil and reduced pressure on the top. This pressure difference is accompanied by a velocity difference, via Bernoulli's principle, so the resulting flow field about the foil has a higher average velocity on one side than the other.
When used as a lifting element on a hydrofoil boat, this upward force lifts the body of the vessel, decreasing drag and increasing speed. The lifting force eventually balances with the weight of the craft, reaching a point where the hydrofoil no longer lifts out of the water but remains in equilibrium. Since wave resistance and other impeding forces such as various types of drag (physics) on the hull are eliminated as the hull lifts clear, turbulence and drag act increasingly on the much smaller surface area of the hydrofoil, and decreasingly on the hull, creating a marked increase in speed.
Early hydrofoils used V-shaped foils. Hydrofoils of this type are known as "surface-piercing" since portions of the V-shape hydrofoils rise above the water surface when foilborne. Some modern hydrofoils use fully submerged inverted T-shape foils. Fully submerged hydrofoils are less subject to the effects of wave action, and, therefore, more stable at sea and more comfortable for crew and passengers. This type of configuration, however, is not self-stabilizing. The angle of attack on the hydrofoils must be adjusted continuously to changing conditions, a control process performed by sensors, a computer, and active surfaces.
The first evidence of a hydrofoil on a vessel appears on a British patent granted in 1869 to Emmanuel Denis Farcot, a Parisian. He claimed that "adapting to the sides and bottom of the vessel a series or inclined planes or wedge formed pieces, which as the vessel is driven forward will have the effect of lifting it in the water and reducing the draught.". Italian inventor Enrico Forlanini began work on hydrofoils in 1898 and used a "ladder" foil system. Forlanini obtained patents in Britain and the United States for his ideas and designs.
Between 1899 and 1901, British boat designer John Thornycroft worked on a series of models with a stepped hull and single bow foil. In 1909 his company built the full scale 22-foot (6.7 m) long boat, Miranda III. Driven by a 60 hp (45 kW) engine, it rode on a bowfoil and flat stern. The subsequent Miranda IV was credited with a speed of 35 kn (65 km/h; 40 mph).
A March 1906 Scientific American article by American hydrofoil pioneer William E. Meacham explained the basic principle of hydrofoils. Alexander Graham Bell considered the invention of the hydroplane a very significant achievement, and after reading the article began to sketch concepts of what is now called a hydrofoil boat. With his chief engineer Casey Baldwin, Bell began hydrofoil experiments in the summer of 1908. Baldwin studied the work of the Italian inventor Enrico Forlanini and began testing models based on those designs, which led to the development of hydrofoil watercraft. During Bell's world tour of 1910–1911, Bell and Baldwin met with Forlanini in Italy, where they rode in his hydrofoil boat over Lake Maggiore. Baldwin described it as being as smooth as flying.
On returning to Bell's large laboratory at his Beinn Bhreagh estate near Baddeck, Nova Scotia, they experimented with a number of designs, culminating in Bell's HD-4. Using Renault engines, a top speed of 87 km/h (47 kn; 54 mph) was achieved, accelerating rapidly, taking waves without difficulty, steering well and showing good stability. Bell's report to the United States Navy permitted him to obtain two 260 kW (350 hp) engines. On 9 September 1919 the HD-4 set a world marine speed record of 114 km/h (62 kn; 71 mph), which stood for two decades. A full-scale replica of the HD-4 is viewable at the Alexander Graham Bell National Historic Site museum in Baddeck, Nova Scotia.
In the early 1950s an English couple built the White Hawk, a jet-powered hydrofoil water craft, in an attempt to beat the absolute water speed record. However, in tests, White Hawk could barely top the record breaking speed of the 1919 HD-4. The designers had faced an engineering phenomenon that limits the top speed of even modern hydrofoils: cavitation disturbs the lift created by the foils as they move through the water at speed above 60 kn (110 km/h; 69 mph), bending the lifting foil.
German engineer Hanns von Schertel worked on hydrofoils prior to and during World War II in Germany. After the war, the Russians captured Schertel's team. As Germany was not authorized to build fast boats, Schertel went to Switzerland, where he established the Supramar company. In 1952, Supramar launched the first commercial hydrofoil, PT10 "Freccia d'Oro" (Golden Arrow), in Lake Maggiore, between Switzerland and Italy. The PT10 is of surface-piercing type, it can carry 32 passengers and travel at 35 knots (65 km/h; 40 mph). In 1968, the Bahraini born banker Hussain Najadi acquired the Supramar AG and expanded its operations into Japan, Hong Kong, Singapore, the UK, Norway and the US. General Dynamics of the United States became its licensee, and the Pentagon awarded its first R&D naval research project in the field of supercavitation. Hitachi Shipbuilding of Osaka, Japan, was another licensee of Supramar, as well as many leading ship owners and shipyards in the OECD countries.
From 1952 to 1971, Supramar designed many models of hydrofoils: PT20, PT50, PT75, PT100 and PT150. All are of surface-piercing type, except the PT150 combining a surface-piercing foil forward with a fully submerged foil in the aft location. Over 200 of Supramar's design were built, most of them by Rodriquez in Sicily, Italy.
During the same period the Soviet Union experimented extensively with hydrofoils, constructing hydrofoil river boats and ferries with streamlined designs during the cold war period and into the 1980s. Such vessels include the Raketa (1957) type, followed by the larger Meteor type and the smaller Voskhod type. One of the most successful Soviet designer/inventor in this area was Rostislav Alexeyev, who some consider the 'father' of the modern hydrofoil due to his 1950s era high speed hydrofoil designs. Later, circa 1970s, Alexeyev combined his hydrofoil experience with the surface effect principle to create the Ekranoplan.
In 1961, SRI International issued a study on "The Economic Feasibility of Passenger Hydrofoil Craft in US Domestic and Foreign Commerce". Commercial use of hydrofoils in the US first appeared in 1961 when two commuter vessels were commissioned by Harry Gale Nye, Jr.'s North American Hydrofoils to service the route from Atlantic Highlands, New Jersey to the financial district of Lower Manhattan.
A 17-ton German craft VS-6 Hydrofoil was designed and constructed in 1940, completed in 1941 for use as a mine layer, it was tested in the Baltic Sea, producing speeds of 47 knots. Tested against a standard E-boat over the next three years it performed well but was not brought into production. Being faster it could carry a higher payload and was capable of travelling over minefields but was prone to damage and noisier.
In Canada during World War II, Baldwin worked on an experimental smoke laying hydrofoil (later called the Comox Torpedo) that was later superseded by other smoke-laying technology and an experimental target-towing hydrofoil. The forward two foil assemblies of what is believed to be the latter hydrofoil were salvaged in the mid-1960s from a derelict hulk in Baddeck, Nova Scotia by Colin MacGregor Stevens. These were donated to the Maritime Museum in Halifax, Nova Scotia. The Canadian Armed Forces built and tested a number of hydrofoils (e.g., Baddeck and two vessels named Bras d'Or), which culminated in the high-speed anti-submarine hydrofoil HMCS Bras d'Or in the late 1960s. However, the program was cancelled in the early 1970s due to a shift away from anti-submarine warfare by the Canadian military. The Bras d'Or was a surface-piercing type that performed well during her trials, reaching a maximum speed of 63 knots (117 km/h).
The USSR introduced several hydrofoil-based fast attack craft into their navy, principally:
The US Navy began experiments with hydrofoils in the mid-1950s by funding a sailing vessel that used hydrofoils to reach speeds in the 30 mph range. The XCH-4 (officially, Experimental Craft, Hydrofoil No. 4), designed by William P. Carl, exceeded speeds of 65 mph (56 kn; 105 km/h) and was mistaken for a seaplane due to its shape. The US Navy implemented a small number of combat hydrofoils, such as the Pegasus class, from 1977 through 1993. These hydrofoils were fast and well armed.
The Italian Navy has used six hydrofoils of the Sparviero class since the late 1970s. These were armed with a 76 mm gun and two missiles, and were capable of speeds up to 50 knots (93 km/h). Three similar boats were built for the Japan Maritime Self-Defense Force.
The French experimental sail powered hydrofoil Hydroptère is the result of a research project that involves advanced engineering skills and technologies. In September 2009, the Hydroptère set new sailcraft world speed records in the 500 m category, with a speed of 51.36 knots (95.12 km/h) and in the 1 nautical mile (1852 m) category with a speed of 50.17 knots (92.91 km/h).
Another trimaran sailboat is the Windrider Rave. The Rave is a commercially available 17-foot (5.2 m), two person, hydrofoil trimaran, capable of reaching speeds of 40 kn (74 km/h). The boat was designed by Jim Brown.
A new kayak design, called Flyak, has hydrofoils that lift the kayak enough to significantly reduce drag, allowing speeds of up to 27 km/h (17 mph). Some surfers have developed surfboards with hydrofoils called foilboards, specifically aimed at surfing big waves further out to sea.
Quadrofoil Q2 is a two-seater, four-foiled hydrofoil electrical leisure watercraft. Its initial design was set in 2012 and it has been available commercially since the end of 2016. Powered by a 5.2-kWh lithium-ion battery pack and propelled by a 5.5 kW motor, it reaches the top speed of 40 km/h and has 80 km of range.
The Manta5 Hydrofoiler XE-1 is a Hydrofoil E-bike, designed and built in New Zealand. Initially designed in secret by Guy Howard-Willis in 2011, it has since been available commercially for pre-order in New Zealand since late 2017  Propelled by a 400 watt motor, it can reach speeds exceeding 14 km/h with a weight of 22 kg. A single charge of the battery lasts an hour for a rider weighing 85kg. 
Soviet-built Voskhods are one of the most successful passenger hydrofoil designs. Manufactured in Russia and Ukraine, they are in service in more than 20 countries. The most recent model, Voskhod-2M FFF, also known as Eurofoil, was built in Feodosiya for the Dutch public transport operator Connexxion.
Current operators of hydrofoils include:
Hydrofoils had their peak in popularity in the 1960s and 70s. Since then there has been a steady decline in their use and popularity for leisure, military and commercial passenger transport use. There are a number of reasons for this:
|Look up hydrofoil in Wiktionary, the free dictionary.|
|Wikimedia Commons has media related to Hydrofoils.|